Xtreme mounting brackets for airdam

[jc71corvette]

Where else could I get the brackets to mount my airdam besides LMC and a dealer?

Also what else would I need besides the brackets? I heard using double sided tape helps installation easier if you done it yourself. True?

[Mikz86TA]

Im not exactly familiar with those specific ones. Im sure the dealer still has them availible. Most of the time each part (bracket, adjuster nut, adjuster screw, etc) are seperate. They might also have it as a grouped part number. Id go by the dealers service/parts dept. and find out. Plus maybe get their price and the part numbers. Sometimes you can run the GM part number on the net and find them cheaper too.

[jc71corvette]

thanks

[Y NI Rider]

Is it a factory air damn. If it is youy wont need two side tape and I would try gettin used brackets are fine. Aftermarkit kits sometimes dont need bracits just the tape but I prfer putting them on. You can fab some up easely, just need bars to brace them from flexin alot. I used thick gage sheet metall to ad them on to my factry brace on my other truck.
What brand you lookin at getting?

[jc71corvette]

Well its OEM Xtreme air dam. I can't believe dealers would still carry that stuff because dimes are discontinued.

[Mikz86TA]

Dealer will cary partsfor cars for a long time. Most of the time they get them from a area warehouse.
I still get some stuff for my 1986 TransAm at the dealer.
Picked up a new hood-to-cowl seal that was in the Jax warehouse, 2 new exhause hangars that are 3rd Gen F-body specific indefinately...one in Jax and the other came from Michican, as well as a plethera of other stuff. Thers still some items I cant get for it tho...but its an 86 so I understand.

[Shadowfax]

www.gmpartsdirect.com carries the parts as well. I'd also check Ebay.

I'm planning to replace my front Air dam soon along with all the brackets and support hardware. Probably will get the air dam off of ebay and the brackets from GM Parts Direct.

[Snafu'03]

I jus had some front end work done on my xtreme not long ago... the body shop got all new valance(air dam) and brackets, supports, all from the dealer... if I can find the invoice I'll post up some part numbers for brackets, supports, valance, ect...

[Shadowfax]

Here is the parts list and their respective numbers:

Xtreme Urethane Ground Effects Parts

15034744 Filler Plate (S-10)
15056110 Filler plate (Blazer)
15034723 Xtreme Airdam
15034715 Front Driver Fender Flare
15034716 Front Passenger Fender Flare
15034711 Standard Cab Driver Skirt
15034712 Standard Cab Passenger Skirt
15034713 Extended Cab Driver Skirt
15034714 Extended Cab Passenger Skirt
15034721 Front Driver Bed Skirt
15034722 Front Passenger Bed Skirt
15034717 Fleetside Rear Driver Flare
15034718 Fleetside Rear Passenger Flare
15034719 Stepside Rear Driver Flare
15034720 Stepside Rear Passenger Flare
15034727 Fleetside Rear Driver Skirt
15034728 Fleetside Rear Passenger Skirt
15034729 Rear Driver Step
15034730 Rear Passenger Step

Mounting Hardware & Fog Lights

Airdam:
16530308 Xtreme Fog Lights (2)
15755954 Headlamp Switch with Fog Lights
15036162 Right Upper Support Bracket
15036163 Left Upper Support Bracket
11516993 Bracket Nut (4)
15037586 Right Lower Support Bracket
15037587 Left Lower Support Bracket
11517803 Push-In Retainer (6)

Flares:

Cab Skirts:

15034750 Standard Cab Skirt Retainer (2)
15034751 Extended Cab Skirt Retainer (2)
15993201 Push-In Retainer (5/Side if Standard Cab, 6/side if Extended Cab)

Bed Skirts/Steps:

15034752 Front Bed Skirt Retainer (2)